Technical data sheets

Contour 21

Straight grab rail 600mm x 35mm diameter

• 600mm length
• 35mm diameter
• Standard white finish (AC)

Satisfies BS 8300-2:2018

Contour 21

Grab rail 400mm x 220mm for back support, Doc M

• 400mm x 220mm
• 35mm diameter
• Doc M back support

Satisfies BS 8300-2:2018

Contour 21

Hinged arm wall support rail 800mm, Doc M compliant

• 800mm arm length
• 35mm diameter
• Aluminium construction
• 3.15 kg
• Doc M compliant

Satisfies BS 8300-2:2018

Contour 21

Folding shower seat, fixed height, 650mm projection

• 650mm projection from wall
• Fixed height
• Folds flat when not in use
• 35mm grab rail diameter

Satisfies BS 8300-2:2018

Contour 21

Angled shower curtain rail 1200 x 1200mm

• 1200 x 1200mm
• 2 kg
• White or blue finish

Contour 21

Doc M Standard Pack, left-hand

• BS 8300 compliant
• Left-hand configuration
• Includes cistern, grab rails and hinged support

Satisfies BS 8300-2:2018

Contour 21

Doc M Contour 21 shower room pack

• 7.5 litres per minute at 3 bar
• Seat height 480mm from floor
• Grab rails at 800mm from floor
• Includes folding seat, grab rails and TMV3 shower valve

Satisfies BS 8300-2:2018

Contour 21

Doc M Contour 21 close coupled pack, left-hand

• BS 8300 compliant layout drawings included
• 50cm Portman 21 basin
• 60cm grab rail x 35mm diameter
• Vitreous china to BS 3402

Satisfies BS 8300-2:2018

Horne Engineering

HORNE 20 thermostatic mixing valve

• 35 to 50 degrees C outlet range
• Factory set at 41 degrees C
• 0.2 to 5 bar inlet pressure
• Hot supply 52 to 85 degrees C
• TMV3 and WRAS approved, LP and HP designations

Satisfies TMV3

Horne Engineering

HORNE 15 thermostatic mixing valve

• 35 to 50 degrees C outlet range
• Factory set at 41 degrees C
• 0.2 to 5 bar inlet pressure
• TMV3 approved, LP and HP designations
• Integral check valves and strainers

Satisfies TMV3

JELD-WEN

SecureSET FD30 flat entrance doorsets

• FD30 30-minute fire integrity and insulation
• Certifire CF5965
• CertiSecure CS5059
• PAS24 enhanced security
• Secured by Design accredited

Satisfies BS 476:Part 22

JELD-WEN

Paintgrade FD30 internal fire doors

• FD30 30-minute fire resistance
• BWF-Certifire certified (CF573, CF192, CF160 depending on model)
• Intumescent strips required top and sides
• 10-year manufacturing guarantee

Satisfies BS 476:Part 22:1987

Vicaima

FD30(S) solid core 44mm fire door

• FD30(S) 44mm solid core
• BM TRADA Q-mark certified
• BWF-Fire Door Alliance Certifire label
• Intumescent seals fitted to door leaf
• Oversized options available on request

Satisfies BS 476 Part 22:1987

Vicaima

Portaro FD30(S) MK2 fire door

• FD30(S) 44mm overall thickness
• Solid particle board core
• Tested to BS 476 Part 22:1987 and EN 1634-1
• EN 13501-2 classified
• 19mm standard undercut

Satisfies BS 476 Part 22:1987 / EN 1634-1

Polyflor

Polysafe Standard PUR safety flooring

• Pendulum test PTV 36 or above (wet)
• 2.0mm or 2.5mm gauge
• 2 metre wide rolls, 20 metre length
• Class Bfl-S1 fire classification (EN 13501-1)
• ISO 10874 use class 23, 34, 43 -- healthcare and commercial

Satisfies EN 13845

Altro

Altro Whiterock Matte hygienic wall cladding

• 2.5mm thickness
• Matte surface finish
• Maximum service temperature 60 degrees C
• Phthalate-free and biocide-free

Altro

Altro Whiterock Satins FR hygienic wall cladding

• 2.5mm thickness
• Sheet 2500 x 1220mm or 3000 x 1220mm
• Fire class B-s2,d0 (EN 13501-1)
• AltroFix W139 adhesive fixed
• Antimicrobial surface -- greater than 99.9% reduction

Satisfies EN 13501-1

Altro

Altro Whiterock Satins hygienic wall cladding (W136/W137)

• 2.5mm thickness
• Sheet 2500 x 1220mm (W136) or 3000 x 1220mm (W137)
• Fire class B-s3,d0 (EN 13501-1)
• 26 satin colours available
• Maximum service temperature 60 degrees C

Satisfies EN 13501-1

Eaton

GuideLED SL self-contained emergency safety luminaire

• 204 to 310 lm emergency output depending on model
• 1, 3 or 8 hour duration selectable
• CGLine+ automatic self-test included as standard
• IP41 rating
• Surface and recessed variants available

Satisfies EN 1838

Eaton

FlexiTech SE LED emergency safety luminaire

• 150 to 600 lm emergency output
• 1, 1.5, 2 or 3 hour duration -- field selectable
• Automatic self-test compliant with EN 62034
• IP43 or IP65 available (IK07)
• 31mm housing depth

Satisfies EN 62034

Sika

G 410-15 EL Felt -- PVC fully-adhered, glass-fleece reinforced roof membrane

• Effective thickness 1.5 mm (-5%/+10%) per EN 1849-2
• Roll size: 15.00 m length x 2.00 m width, roll weight 66.00 kg
• Shelf life 5 years from date of production
• Storage temperature +5degC to +30degC, store horizontally, do not stack pallets
• Multi-layer, lacquered matt-finish, heat-weldable PVC sheet with glass fibre reinforcing inlay and polyester fleece backing

Satisfies EN 13956 (CE Marking and Declaration of Performance)

Sika

D-15 RoofPro Advanced -- 1-part polyurethane liquid-applied waterproofing membrane

• BBA certified (No. 21/5863); UK Technical Assessment No. UKTA-0836-23/6853; Declaration of Performance No. 55578297
• Tensile strength ~13 N/mm2 reinforced, ~6 N/mm2 unreinforced (ISO 527-1/3)
• Thermal/service resistance -20degC to +80degC; minimum substrate/ambient application temperature +2degC
• Reaction to fire: Euroclass E (EN 13501-1); initial Solar Reflectance 0.87, Thermal Emittance 0.88, SRI 110
• Shelf life 12 months from date of production

Satisfies EN 13501-1 (Reaction to Fire); BBA certified No. 21/5863

Kemper System

2K-PUR Waterproofing -- cold-applied, fleece-reinforced polyurethane resin liquid roofing system

• Usage guide: at least 3.0 kg/m2 depending on layer thickness required
• Workability time approx. 30 min; rainproof after approx. 2 h; walkable after approx. 16 h; cured after approx. 72 h
• External fire performance BROOF(t1); reaction to fire Euroclass E (EN 13501-1/5)
• Resistance to wind loads >= 50 kPa
• Short-term temperature resistance 250degC; root resistant per FLL testing; 2-component, solvent-free, cold-applied

Satisfies ETAG 005 (ETA 03/0044)

Scott Bader

CrysticROOF Repair -- thixotropic, fibre-reinforced one-component polyurethane liquid membrane for repairing GRP roofs

• Tack-free time at 23degC & 55% RH: 2-3 hours; recoat time 6-48 hours
• Tensile strength at break at 23degC: 8.5 N/mm2; elongation at 23degC >200%
• Service temperature range -40degC to +80degC; max short-time (shock) temperature 200degC
• Passed QUV accelerated weathering test (2000 hours)
• Hardness Shore A 70; supplied in 15 kg containers; shelf life 12 months from manufacture

IKO (IKO Polymeric)

Armourplan P -- polyester scrim reinforced PVC-P membrane for mechanically fastened/adhered roofing

• Thickness 1.2 mm; roll widths 1.06 m / 2.12 m; roll length 20 m
• Material PVC-P with woven polyester scrim reinforcement
• BBA Agrement Certificate No. 05/4287
• Colours: Mid Grey (nearest RAL 7046), Slate Grey (nearest RAL 7015)
• Mechanically fastened using IKOfix Stress Plates and IKOfix Screws; also usable loose-laid ballasted or adhered

Satisfies BBA Agrement Certificate No. 05/4287; CE marked

BMI (Icopal)

Tecnatorch Torch On Mineral Capsheet -- polyester reinforced SBS-modified bitumen membrane

• Roll dimensions 8 m x 1 m; mass per unit area 5 kg/m2 (+/-0.15); effective thickness 4.2 mm (+/-0.2)
• External fire performance BROOF(t4) per BS EN 13501-5
• Tensile strength 900 N/50mm (MD and TD), +/-35% tolerance (BS EN 12311-1)
• Flexibility at low temperature <= -15degC (BS EN 1109); flow resistance at elevated temperature > 90degC (BS EN 1110)
• Polyester reinforcement 195 g/m2; BBA certificate number 07/4409 (PS4)

Satisfies EN 1848-1, EN 13501-5, EN 12311-1; BBA certified 07/4409 (PS4)

Elevate (Holcim, formerly Firestone)

RubberCover EPDM Membrane -- 100% cured EPDM synthetic rubber membrane, LSFR (Low Slope Fire Retardant)

• Declared thickness values 1.1 mm and 1.5 mm (EN 1849-2); mass per unit area 1.35 kg/m2 and 1.85 kg/m2 respectively
• Tensile strength >= 7 N/mm2 (L/T); elongation >= 300% (L/T) per EN 12311-2 (B)
• Foldability at low temperature <= -45degC (EN 495-5); resistant to temperature shocks up to 130degC
• UV exposure: Pass (>= 7500 h) per EN 1297
• Reaction to fire: Euroclass E (EN 13501-1); roll widths 3.05-6.10 m depending on thickness, length 7.62 m

Satisfies EN 1849-2 (declared thickness); EN 13501-1 (reaction to fire)

Hambleside Danelaw

Dryseal Semi-rigid Warm Roof System -- GRP thermoset single-layer roof covering with liquid-applied top coat

• Tested to BS 476-3:1975 extended fire exposure roof test; designated FAC
• Life expectancy stated by manufacturer as "in excess of 30 years", subject to environmental/specification factors and maintenance
• Leak-free insurance-backed guarantee of 20 years when installed to the manufacturer's Technical Manual
• Mechanically attached with adhesive bonding to roof perimeter trims only
• Compatible with cold, warm and inverted roof build-ups; not suitable over strawboard decking

Satisfies BS 476-3:1975 (extended fire exposure roof test -- designated FAC)

Marley

Mendip Concrete Interlocking Tile

• Minimum pitch 15deg at 100mm headlap (smooth) or 17.5deg at 75mm headlap
• Maximum pitch 90deg
• Tile size 420 x 330mm, cover width 298mm (nominal)
• Covering capacity 9.7 tiles/m2 at 75mm headlap, 10.5 tiles/m2 at 100mm headlap
• Weight of tiling 46kg/m2 (0.4 kN/m2) at 75mm gauge, 49kg/m2 (0.48 kN/m2) at 100mm gauge

Satisfies BS EN 490 / BS EN 491

Russell Roof Tiles

Galloway Concrete Roof Tile

• Manufactured to BS EN 490 and BS EN 491; non-combustible to BS 476: Part 3:2004
• Minimum pitch 22.5deg (100mm headlap), 25deg (75mm headlap smooth), 30deg (75mm headlap granular); max pitch 60deg subject to fixing spec
• Tile size 418 x 330mm, covering width 298mm
• Weight of tiling approx. 53kg/m2 at 75mm headlap, 58kg/m2 at 100mm headlap
• Guaranteed for 60 years from date of supply

Satisfies BS EN 490 / BS EN 491

Sandtoft (Wienerberger)

Old English Clay Pantile

• Material: clay; minimum roof pitch 30deg; headlap 75mm
• Tile size 365 x 250mm; cover width 200mm; covering capacity 17.3 tiles/m2
• Weight as laid 41.6kg/m2; weight per tile 2.4kg
• Batten size 38 x 25mm up to 450mm rafter centres, 50 x 25mm up to 600mm centres
• Fixing must comply with BS 5534 and BS 8000: Part 6

Satisfies BS 5534

Sandtoft (Wienerberger)

Shire Concrete Pantile

• Material: concrete; minimum pitch 17.5deg smoothfaced at 100mm headlap, 22.5deg smoothfaced at 75mm headlap, 30deg sandfaced at 75mm headlap
• Tile size 380 x 230mm; cover width 200mm; covering capacity 17.9 tiles/m2 at 100mm, 16.4 tiles/m2 at 75mm
• Weight as laid 50.7kg/m2 at 100mm headlap, 46.5kg/m2 at 75mm headlap
• Headlap range 75mm (min) to 120mm (max)
• Fixing must comply with BS 5534 and BS 8000: Part 6

Satisfies BS 5534

Welsh Slate

Penrhyn Capital Grade Roofing Slate

• System of Attestation of Constancy of Performance = AVCP System 4
• Nominal thickness 5.5mm; individual thickness tolerance < +/-35%
• Mechanical resistance (characteristic modulus of rupture): transverse 78.3 N/mm2, longitudinal 41.7 N/mm2
• Water permeability/absorption classified W1 (0.6%)
• Sulphur dioxide exposure class S1; thermal cycling class T1

Satisfies BS EN 12326-1:2014

Burlington Slate (Burlington Stone)

Burlington Blue/Grey Roofing Slate

• Meets BS EN 12326: Water Absorption class W1 (<=0.6%), Thermal Cycle Resistance class T1, Sulfur Dioxide Exposure class S1
• Manufacturer states technical characteristics "ensure a life span of over 150 years" (manufacturer claim, not independently verified against a third-party test)
• Company holds ISO 14001 environmental accreditation
• Supplied in three formats: Randoms, Sized, and Patterns

Satisfies BS EN 12326

Swisspearl (formerly Cembrit)

Swisspearl Jutland Fibre Cement Slate

• Manufactured in accordance with EN 492; achieved Class B (highest class) for structural stability under EN 492
• Dimensions 600 x 600mm, thickness 4.0mm
• Density, dry (EN 492): 1820 kg/m3; weight 2.62 kg/piece
• Manufactured to ISO 9001 and ISO 14001
• EPD number EPD-CEM-20160113-IAD1-EN

Satisfies EN 492

Klober

AIR160 Roof Underlay

• Manufactured to BS EN 13859-1:2010; BBA Certificate Number 07/4435
• Weight 160 g/m2 (EN 1849-2); water vapour transmission SD value 0.009m (EN 12572)
• Resistance to water penetration W1 (EN 1928)
• Tensile strength MD/CD 280/200 N/50mm (EN 12311-1); nail tear strength MD/CD 140/130 N (EN 12310-1)
• Fire rating Class E (EN 13501-1 / EN 11925-2)

Satisfies BS EN 13859-1:2010; BBA Certificate No. 07/4435

Klober

Permo Extreme Low-Pitch Roof Underlay

• Minimum roof pitch enabled: 12.5deg for interlocking tiles, 15deg for slates, 22.5deg for plain tiles
• Weight 240 g/m2 (EN 1849-2); water vapour transmission SD value 0.08m (EN 12572)
• Tensile strength MD/CD 310/360 N/50mm (EN 12311-1); nail tear strength MD/CD 215/200 N (EN 12310-1)
• Resistance to temperature -40degC to +80degC
• Resistance to water penetration W1 (EN 1928); fire rating Class E

Glidevale Protect

TF200 Thermo Low Emissivity Insulating Breather Membrane

• Aged thermal resistance 0.77 m2K/W, aligned with STA Advice Note 18, using typical 600mm stud centres
• Class 1 surface spread of flame to BS 476-7
• BM TRADA independently certified for all applications
• Roll sizes: 0.3, 0.6, 2.7, 3.0m x 100m and 1.5m x 50m

Associated Lead Mills

Craftsman's Guide to Rolled Lead Sheet (Codes 3-8)

• Rolled lead sheet is the only lead sheet produced to a British/European Standard, BS EN 12588
• Sheet thickness consistency tolerance must not exceed +/-5% at any one point (BS EN 12588)
• Code 3: thickness 1.32mm, weight 14.97 kg/m2, use category (A) -- flashings
• Code 4: thickness 1.80mm, weight 20.41 kg/m2, use category (ABF) -- flashings/roofing/gutters
• Density of lead 11,340 kg/m3; melting point 327degC

Satisfies BS EN 12588

Marley

Clay Plain Tiles Fixing Guide

• Covers storage & handling, underlays, battens, cutting, flashings & weatherings, valleys, ridges, hips, verges, dry-fix and ventilation systems for clay plain tiles
• Issued November 2018
• Includes Universal RidgeFast dry-fix system and Universal Dry Valley/Hipfast systems

Sika (formerly Cromar Building Products)

SikaRoof Vent3 Breather Membrane

• Sd (vapour resistance) value of 0.02 m
• Water tightness class W1
• Triple-layer spun-bonded polypropylene construction, felt weight ~135 g/m2 (+/-10%)
• Requires counter-battens when fully supported (e.g. over sarking boards); fixed at 200mm centres with min. 25mm airspace between underlay and tiles
• Max recommended UV exposure before covering: 3 months. Note: sheet did not explicitly cite BS EN 13859-1 or state an LR/HR classification.

IKO

IKO Pitched Roof Underlay

• Sd value of 15m -- relatively high vapour resistance, closer to a traditional low-permeability product than a breathable LR membrane
• Water tightness class W1 (per EN 1928)
• Mass 116 g/m2
• Fully supported installations (e.g. over sarking boards) must incorporate counter-battens
• Described by IKO as a secondary barrier only, not a primary weatherproofing layer

Satisfies EN 13859-1

IKO

IKO Rubershield Pro

• Classified by IKO as a Low Resistance (LR) membrane, 140 g/m2
• Sd value 0.04m; water tightness class W1 (per EN 1928)
• BBA certified -- Agrement Certificate 15/5190
• Three-layer polypropylene, fixed with clout nails to rafters (not self-adhesive)
• Fire rating Euroclass E (EN 13501-1:2007); tensile strength LD 240N/50mm, TD 150N/50mm

Satisfies BS 5534:2014; BBA Agrement Certificate 15/5190

DuPont

DuPont Tyvek Supro

• Sd value nominal 0.02 m (range 0.005-0.035 m)
• Water tightness class W1, water column rating 2.3 m per EN 20811
• Mass 145 g/m2 nominal (range 136-154 g/m2); thickness 0.490mm
• Construction: HDPE and PP composite, available with or without integrated tape (product code 2507B)
• Sheet did not state an explicit LR/HR classification or warm-roof (non-ventilated) approval -- a separate DuPont BBA document for non-ventilated use exists on the same domain but was not itself verified in this pass

Satisfies EN 13859-1:2010 / EN 13859-2:2010

Marley Alutec

Aluminium Ogee Gutter System

• Aluminium ogee-profile eaves gutter system designed to replicate traditional cast-iron gutter aesthetics.
• Not yet content-verified against the PDF body -- confirm material spec, coating and fixing details before quoting a number from this sheet.

Marley Alutec

Evoke Fascia Type C System

• Aluminium fascia system, manufacturer product data sheet with specification clause wording.
• Not yet content-verified against the PDF body -- confirm board thickness, finish/coating range and fixing method before quoting.

Marley Alutec

Aluminium Fascia & Soffit System -- Installation Guide

• Installation guide covering fascia and soffit fitting sequence for the Evoke aluminium system.
• Not yet content-verified against the PDF body -- confirm fixing centres and ventilation strip integration before quoting.

FloPlast

PVCu Rainwater Systems -- Technical Data

• Technical data document covering FloPlast's PVCu gutter and downpipe range.
• Not yet content-verified against the PDF body -- confirm dimensions, flow capacities and standards references before quoting.

FloPlast

Rainwater Systems -- Kitemark Certificate

• BSI Kitemark certificate covering FloPlast rainwater products (certificate number and scope confirmed on the page listing this document; PDF body not itself content-verified).

Satisfies BS EN 607

FloPlast

Rainwater Installation Guide

• Installation guide for the 112mm half round PVCu gutter system, covering fixing and jointing.
• Not yet content-verified against the PDF body -- confirm bracket spacing and fall/gradient recommendations before quoting.

Brett Martin

PVCu Gutter Systems -- Technical Guide

• Full technical guide covering Brett Martin's PVCu rainwater gutter and downpipe range.
• Not yet content-verified against the PDF body -- confirm capacity tables and standards references before quoting.

Swish Building Products

Jumbo and 16mm Fascia Boards

• Technical sheet for Swish PVCu fascia board range (Jumbo and 16mm profiles).
• Not yet content-verified against the PDF body -- confirm board depth/thickness options before quoting.

Smart Systems

Alitherm 400 aluminium window system

• Window U-value 1.4 W/m2K
• PAS 24:2016 approved for enhanced security, compliant with Building Regs Part L
• 70mm frame depth, max fixed window size 2100mm x 2100mm
• Air permeability Band A Class 4, wind resistance 2000+ Pa, water tightness Class 4

Satisfies PAS 24:2016

Senior Architectural Systems

SPW600e AOV (Automatic Opening Vent) aluminium window system

• U-values 1.4 W/m2K double glazed, 1.0 W/m2K triple glazed
• Air permeability and water tightness rated to 600 Pa, wind resistance to 2400 Pa
• Three-chamber 75mm polyamide thermal-break profile
• Relevant where a window doubles as a smoke ventilation outlet, not just a standard opening light

Satisfies BS 6375-1

REHAU

REHAU uPVC window and door systems

• ECOTEC casement Uw 2.1 W/m2K; PURELINE casement Uw 2.9 W/m2K; AGILA high slider Uw 1.6 W/m2K
• Profile depths: PURELINE 36mm single chamber, ECOTEC 60mm three chamber, AGILA 86-160mm
• Sound insulation up to 32dB (PURELINE) or 40dB (ECOTEC)
• URL confirmed live via fetch tool but direct curl access was blocked by the manufacturer's bot protection during this research pass -- re-verify with a browser before treating as fully confirmed if strict certainty is needed

Timber Windows

Timber casement and sash window range -- product guide

• Centre-pane U-value 1.1 W/m2K, double glazed, argon-filled, low-conductivity spacer bars
• Claimed 80% energy saving versus single glazing, 45% versus ordinary double glazing
• This document reads as a 2018 product/marketing guide rather than a formal numbered technical data sheet -- no other directly-verifiable UK timber window manufacturer sheet was found in this pass, flagged as the weakest-sourced entry in this category rather than omitted outright

Pilkington (NSG Group)

Laminated safety and security glass

• EN 12600 impact classification 2(B)2 for standard safety builds (4.4mm-10.4mm), 1(B)1 for thicker 6.8mm+ builds
• Security grades P2A to P8B per EN 356; bullet-resistant grades BR2S to BR7S per EN 1063
• Ug-values approximately 4.4 to 5.7 W/m2K depending on thickness and build

Satisfies BS EN 12600

Selectaglaze

Secondary glazing product and performance guide

• Acoustic reduction up to 56dB combined with a double-glazed primary window; typically 45dB with a 100mm+ cavity
• Thermal U-values 1.627-3.000 W/m2K depending on series and cavity, best example 1.27 W/m2K
• Security rated to PAS 24:2016 and LPS 1175 SR1-SR3
• A well-established route to upgrading acoustic and thermal performance without replacing the primary window -- relevant where original windows are retained for heritage or cost reasons

Satisfies BS EN ISO 140-3:1995; PAS 24:2016

Jackloc

Pro 5 key-lockable cable window restrictor

• Restricts opening to 100mm (89mm option available to prevent passage of a small child)
• Independently tested and passed to BS EN 13126-5:2011 for opening, durability, mechanical load, percussion, impact and cutting resistance
• Load performance tested 100-400% above the historic BS 6375-2:1987 600N benchmark, depending on frame material
• Compatible with uPVC, timber, aluminium, steel and composite frames -- the type of product used to meet the Regulation 14 falls-from-height duty in a care home, though the sheet itself does not cite Regulation 14 by name

Satisfies BS EN 13126-5:2011

K Rend

Silicone K1, one-coat water-repellent silicone render

• Kitemarked and CE marked; Compressive Strength category CS II, Capillary Water Absorption category W2
• Coverage roughly 1.6kg per mm thickness per m2; nominal 16-20mm thickness needs roughly 26-32kg/m2
• Applied in two spray passes -- first pass 4-8mm, second pass to 12-14mm finish

Satisfies BS EN 998-1:2010

Kingspan Insulation

K15 Rainscreen Board

• Thermal conductivity as low as 0.021 W/mK, declared 0.022 W/mK at 25-44mm thickness
• Declared compressive strength 100 kPa (BS EN 826:2013)
• Assessed per BS 8414-1/-2:2020 and BS 9414:2019 for cladding fire performance -- relevant post-Grenfell for a care home classed as a relevant building under Approved Document B
• Rigid thermoset phenolic foam core, standard board size 2400mm x 1200mm

Satisfies BS EN 13166:2012+A2:2016; BBA Certificate 14/5134

Rockwool

RainScreen Duo Slab, stone wool insulation for ventilated rainscreen/brick-slip cladding

• Euroclass A1 non-combustible per EN 13501-1
• Thermal conductivity 0.034 W/mK below 90mm, 0.035 W/mK at 90mm or above
• Dual-density technology -- higher-density outer face for fixings, softer underside for uneven substrates
• Acoustic performance up to Rw 62dB in typical systems

Satisfies BS EN 13501-1:2018; BBA Certificate 17/5402

Sika

Sika-1 Pre-bag LC render mortar, three-coat waterproof render system

• Compressive strength 50 MPa or greater (EN 12190); flexural strength 8.0 MPa or greater (EN 196-1)
• No water penetration after 72 hours at 5 bar negative pressure
• Three-layer system, minimum 18mm total (6mm bonding, 6mm render, 6mm finishing coat)
• This is a Type A tanking/waterproofing render rather than a cosmetic repointing product -- specify accordingly if a decorative repoint rather than waterproofing is what is actually needed

Satisfies BS 8102:2022 (Type A waterproofing)

Flexcrete Technologies

Monolite, Class R2 lightweight repair mortar for concrete, brick and stone

• CE marked to EN 1504-3 Class R2
• Compressive strength 13 MPa or greater at 1 hour, 30 MPa or greater at 28 days
• Applied 5-100mm in a single layer, including overhead work
• Single-component, polymer-modified, fibre-reinforced -- mixed only with water

Satisfies BS EN 1504-3, Class R2

Keim Mineral Paints

Soldalit silicate/silicone-resin hybrid facade paint

• Non-flammable, fire class A2-s1,d0 per EN 13501-1
• Water vapour diffusion equivalent air layer thickness (sd) 0.01m or less, class V1, highly permeable
• Water permeability under 0.1 kg/(m2 x h^0.5), class W3, highly water-repellent
• A breathable coating for masonry that needs to shed water without trapping vapour behind it, rather than a film-forming sealant

Satisfies BS EN 13501-1 (fire, Class A2-s1,d0)

Weber (Saint-Gobain)

weberend MPR, pre-blended sand/cement/lime undercoat render

• Formulated to comply with BS 5262 mix designations
• Approximately 1.8kg/m2 coverage per mm of thickness, roughly 27.5 m2/tonne at 20mm
• Applied in two coats to 20mm total, or two spray passes
• URL confirmed to exist on the manufacturer's own domain but the raw PDF could not be independently parsed in this pass (bot-challenge blocked direct access) -- treat the figures above as lower confidence than the rest of this category and re-verify via a browser before relying on them for a spec

Satisfies BS 5262

Marshalls

Priora 200 x 100 x 60mm permeable block paving

• Characteristic tensile splitting strength 3.6 MPa or greater, minimum failing load 250 N/mm
• Polished and unpolished skid resistance value (PSRV/USRV) both greater than 45
• Reaction to fire Class A1; coverage 50 units per m2
• Permeable block paving -- relevant to SuDS surface water requirements on a car park or parking bay resurfacing job

Satisfies BS EN 1338:2003

Marshalls

Titan Kerb 1000, 400 x 390 x 1000mm heavy-duty precast concrete kerb

• Characteristic bending strength 3.5 MPa, no individual result below 2.8 MPa
• Abrasion resistance 23mm or less (Wide Wheel Abrasion Test)
• Freeze-thaw resistance 1.0kg/m2 mean or less, no individual value above 1.5kg/m2
• PSRV and USRV both greater than 45; reaction to fire Class A1

Satisfies BS EN 1340:2003

Brett Landscaping

Beta block paving

• Unpolished PTV (slip resistance value) 55 or greater -- rated low slip potential
• Characteristic tensile splitting strength 3.6 MPa or greater, failing load 250 N/mm or greater
• Abrasion Class 4 (20mm or less, Wide Wheel Test); freeze-thaw Class 3
• Sizes available: 105x140mm, 140x140mm and 210x140mm, both 60mm and 80mm depths

Satisfies BS EN 1338:2003

Tobermore

Pedesta block paving, 200 x 100mm

• Available in 50mm, 60mm and 80mm depths, all at 50 blocks per m2 coverage
• Wear-resistant surface layer minimum 4mm, over 350kg/m3 cement content
• PSRV and USRV both greater than 45 (mean); freeze-thaw Class 3
• Reaction to fire Class A1

Satisfies BS EN 1338:2003

Marshalls

Saxon textured concrete paving slab, 450 x 450 x 70mm

• Unit weight 32kg; PSRV and USRV both greater than 45
• Loading Category 6, rated for up to 10 large goods vehicles weekly
• Freeze-thaw resistance 1.0kg/m2 mean or less, no individual value above 1.5kg/m2
• Reaction to fire Class A1; coverage 4.9 units per m2

Satisfies BS EN 1339:2003

Tarmac

Ulticolour coloured asphalt

• SMA 6mm grade: texture depth under 1.0mm, layer thickness 25-40mm, typical use driveways/footpaths/cycleways
• SMA 10mm grade: texture depth 1.1-1.5mm, layer thickness 30-45mm, typical use car parks/carriageways
• Porous grades available for SuDS surface water applications, layer thickness 25-45mm
• BBA-accredited production; this document reads as general technical/product information rather than a single numbered BS EN test-result sheet -- separate BBA certificates exist for each grade if a formal certificate is needed

Addagrip

Addaset UV-stable resin bound surfacing

• Skid resistance (TRL 176): pedestrian 55 or greater, vehicular 60 or greater
• Depth options: 3mm aggregate at 12mm system depth, 6mm at 18mm, 10mm at 22mm
• Permeability 4.46-30 litres/sec/m2 depending on system depth -- relevant to SuDS surface water requirements
• Full chemical cure 7 days; additional slip-resistance grit application available

Satisfies TRL 176 (skid resistance); BS EN 12697-40:2005 (permeability)

Furnitubes

Zenith stainless steel bollard

• Material 304 stainless steel standard, 316 stainless steel for coastal/aggressive environments
• Heights 900mm or 1000mm above ground, diameters 102mm, 115mm, 140mm or 170mm
• Root-fixed, removable, security-core and baseplated fixing options available
• This is a standard pedestrian/traffic-calming bollard -- it is not rated to PAS 68 or IWA 14 for hostile-vehicle mitigation, source separately if that level of protection is specified

Wavin

OsmaDrain below ground drainage system

• Nominal pipe diameters 110mm and 160mm, PVC-U pipe and fittings
• Ring-seal and solvent-weld jointing methods; solvent cement cure time 24 hours
• Pipe stiffness class SN8 (8kN/m2); maximum installation depth 10m
• Rodding eye access covers rated to 15kN; ductile iron gratings up to 35kN or 125kN depending on spec

Satisfies BS EN 1401-1:2009; BBA Certificate 87/1835

Wavin

OsmaDrain yard gully

• Internal diameter 295mm, depth 605mm, approximately 26 litre holding capacity
• Blow-moulded HDPE body with integral trap and TPE plug
• Rated to accept Class B125 covers per BS EN 124:2015
• Quoted service life over 50 years

Satisfies BS EN 124:2015; BBA Certificate 19/5622

Wavin

AquaCell 160 stormwater/attenuation crate

• Void ratio greater than 95% by volume
• Long-term static load strength up to 2,000kg/m2; dynamic trafficability load up to 800kg/wheel with adequate cover
• Unit size 1100mm x 1100mm x 160mm, storage volume over 185 litres per unit
• 100% recycled polypropylene, frost/acid/hydrocarbon/rot resistant -- sheet did not state a specific BS/EN standard

Naylor Drainage

MetroDrain twin wall HDPE pipe system

• Internal diameter range 100mm to 1050mm across the range
• Twin-wall HDPE construction: smooth bore, corrugated outer wall
• Pipe stiffness classes SN6 and SN4 to ISO 9969
• BBA approved and adoptable under Highways Act 1980 / SHW Table 5/1

Satisfies ISO 9969

Hauraton

Slotted channel 100, Type 010, 1.0m

• Loading capacity range A15 to D400 to EN 1433, so specifiable from a pedestrian path up to vehicle-trafficked areas
• Channel dimensions 1000mm x 160mm x 200mm, internal cross-section 142.0cm2
• Recycled, modified polypropylene channel body
• DN/OD 110 vertical outlet connection

Satisfies BS EN 1433

EJ (EJCo)

Access covers and gully gratings product guide

• D400 class covers: test load 400kN, for carriageways, hard shoulders and parking areas
• B125 class covers: test load 125kN, for car parks and pedestrian areas with infrequent vehicle access
• Ductile iron standard material, manufactured to BS EN 124 and ISO 9001
• Frame depths typically 25-150mm depending on load class and application

Satisfies BS EN 124

BRAWO Systems (Brawoliner)

Brawoliner 3D, no-dig cured-in-place-pipe (CIPP) drain lining

• Pipe diameter range DN70-DN400, capable of lining bends up to 90 degrees
• Cured wall thickness 3.0-5.5mm depending on variant
• Textile carrier tube with polyurethane foil coating, no-dig CIPP rehabilitation method
• No explicit EN/ISO standard number is printed on this specific document -- the relevant UK context is the platform's existing "line existing drain" job, which this product matches for method rather than a cited standard

Altro

Altro Aquarius safety flooring

• 2mm total thickness, 2mm wear layer
• Pendulum Test Value 50 or above (Slider 96) -- R11 slip rating (EN 16165 Annex B / ASR A1.5)
• Fire classification Bfl-s1 (EN 13501-1)
• Bio-plasticiser, ortho-phthalate-free formulation
• Antistatic, 2kV or below

Satisfies EN 13845

Altro

Altro Walkway 20 safety flooring

• 2mm thickness, 2mm wear layer
• PTV 36 or above, ramp test DS 0.30 or above -- R10 slip rating (EN 16165 Annex B / ASR A1.5)
• Fire classification Bfl-s1 (EN 13501-1)
• Antistatic, 2kV or below (EN 1815 / EN 1081)
• Floorscore and CDPH 1350 approved

Satisfies EN 13845

Altro

Altro Wood Comfort safety flooring

• 2.85mm total thickness, 0.7mm wear layer, roll 2m x 20m
• PTV 36 or above, DS 0.30 or above -- R10 slip rating
• Sound insulation reduction approximately 14dB
• Fire classification Cfl-s1 (EN 13501-1)
• Castor chair rated Type W; antistatic 2kV or below (EN 1815)

Satisfies EN 13845

Polyflor

Expona Commercial PUR luxury vinyl tile

• Overall gauge 2.5mm (ISO 24346/EN 428); wear layer 0.55mm (ISO 24340/EN 429)
• Use classification ISO 10874 (EN 685) 23, 33, 42 -- suitable for heavy commercial/healthcare traffic
• Slip resistance Class DS, R10, 0.5 or above (EN 13893/DIN 51130)
• Fire classification Bfl-s1 (EN 13501-1)
• Planks from 101.6mm x 914.4mm up to 203.2mm x 1524mm; tiles up to 609.6mm x 1219.2mm

Satisfies ISO 10874 (EN 685)

Polyflor

Polysafe Verona PUR (Original) safety flooring

• 2.0mm thickness (ISO 24346/EN 428)
• Pendulum 36 or above wet (4S Rubber/Slider 96) -- R10 (DIN 51130/DIN EN 16165)
• Conforms to EN 13845 and ASTM F1303 Type II Grade I Class B
• Use areas ISO 10874 23/34/43
• Fire classification Bfl-s1 (EN 13501-1)

Satisfies EN 13845

AKW

Tuff Form wet floor former

• Sizes from 900x900mm up to 1800x820mm (10 sizes)
• Load rating up to 60 stone / 381kg bearing weight on joists (unlimited on concrete)
• Material: SMC-GRP (Sheet/Compression Moulded Glass Reinforced Plastic)
• Fall to waste 15mm; ribbed underside to eliminate slippage during installation
• Lifetime warranty (excludes wear and tear, first installation only)

AKW

Larenco Duo Care glass screen

• 6mm clear toughened safety glass, tested to EN 12150 / ANSI Z97.1 / CGSB-12.1-M90
• Two half-height bi-parting doors (900mm door height)
• Sizes 800x800, 900x900, 1000x1000, 1100x1100mm, with 20mm profile adjustment per side
• Bright chrome finish, magnetic corner seals
• "Stay Clear" easy-clean glass coating

Satisfies EN 12150

AKW

Larenco single sliding glass screen

• 6mm clear toughened safety glass
• Sizes 1200mm (adjustable 1190-1230mm) and 1400mm (adjustable 1390-1430mm) wide, 2000mm high
• Glass tested to EN 12150 / ANSI Z97.1 / CGSB-12.1-M90; screen tested to EN 14428 / IGC154 / CSA B45
• Aluminium polished profile frame, bright chrome finish
• Magnetic cushion seals

Satisfies EN 12150 / EN 14428

AKW

4000 Series standard shower seat

• Height adjustable 390-640mm, width 810-1060mm, depth 460mm, seat depth 250mm
• Load capacity 254kg / 40 stone
• Rust-proof stainless steel construction
• Tested to BS EN 12182:1998 and BS EN 12727:2000
• Fine adjustment (13mm) for uneven floors; lifetime warranty (first installation only, excludes wear and tear)

Satisfies BS EN 12182:1998 & BS EN 12727:2000

AKW

4000 Series shower seat with back and arms

• Same core dimensions and load rating as the 4000 Series standard seat -- 254kg / 40 stone
• Back height 576mm, arm width 442mm
• Padded back and arms available in blue or grey
• Independent folding arms for side transfers
• Tested to BS EN 12182:1998 and BS EN 12727:2000

Satisfies BS EN 12182:1998 & BS EN 12727:2000

AKW

4000 Series large/extra wide shower seat

• Width 585mm, seat depth 580mm, depth 562mm, height adjustable 390-640mm
• Load capacity 254kg / 40 stone
• Rust-proof stainless steel, white/blue/grey options
• Tested to BS EN 12182:1998 and BS EN 12727:2000
• Lifetime warranty (first installation only)

Satisfies BS EN 12182:1998 & BS EN 12727:2000

AKW

Stainless steel straight grab rail

• 32mm diameter; lengths 300mm, 450mm, 600mm
• Max central load 150kg / 23.5 stone
• High-grade stainless steel, rustproof
• Tested to BS EN 12182:1999
• 56mm wall clearance, 3 fixing points, captive flange covers

Satisfies BS EN 12182:1999

Sika

Sika MonoTop-615 repair mortar

• One-component, cement-based, polymer-modified high-build concrete repair and reprofiling mortar, meeting EN 1504-3 Class R3
• Compressive strength approximately 30 N/mm2 at 7 days and approximately 35 N/mm2 at 28 days (Class R3 requires over 25 N/mm2 at 28 days per EN 12190)
• Tensile adhesion strength greater than 2 N/mm2 to EN 1504-3 clause 5.5
• Hardened mortar density approximately 1.89 kg/l after 28 days; coverage guide approximately 1.65 kg/m2 per mm thickness

Satisfies EN 1504-3 Class R3

Helifix

HeliBar helical masonry crack stitching bar

• Helical reinforcing bar in austenitic stainless steel Grade 304 or 316, available in 4.5mm, 6mm, 8mm and 10mm diameters
• Tensile strength (6mm HeliBar) approximately 900 N/mm2 in Grade 304, approximately 840 N/mm2 in Grade 316
• Installed into a resin-filled slot in the bed joint, typically extending at least 500mm either side of a crack, at vertical spacing of every 4-6 courses
• For cavity walls where both leaves are cracked, both sides of the wall must be stitched to fully arrest movement

Sika

Sikaflex Construction Purform facade and masonry joint sealant

• One-part, non-sag, low-modulus polyurethane sealant for movement joints in concrete and masonry facades
• Movement capability plus or minus 25 percent to EN ISO 9047 (plus or minus 50 percent to ASTM C719); ASTM C920-18 Movement Class 50
• Elastic recovery 90 percent (EN ISO 7389); Shore A hardness greater than 20 after 28 days cure (EN ISO 868)
• Service temperature range minus 40C to plus 70C once fully cured

Satisfies EN 15651-1 Class F EXT-INT CC 25 LM

Marley Alutec

Traditional Half Round aluminium gutter system

• Marine grade 6063 T5 aluminium extrusion with LM6 cast fittings, profiled to the traditional cast-iron half-round profile of BS 8530:2010
• Polyester powder coat finish to BS EN 12206-1:2004
• Available in 100mm, 113mm and 125mm nominal sizes; flow rate for the 125mm gutter is approximately 1.27 l/s (end outlet) or 2.54 l/s (centre outlet)
• Manufacturer-stated functional life expectancy of 50-plus years with minimal maintenance

Satisfies BS 8530:2010

Safeguard Europe

Stormdry Masonry Protection Cream

• Deep-penetrating water-repellent silicone cream for external masonry, BBA-accredited with a 25-year service life (BBA Certificate 15/5198)
• Coverage approximately 5m2 per litre in a single-coat application; penetration depth approximately 12mm on Fletton brick
• Bridges hairline cracks up to 0.3mm wide
• Minimum application temperature 5C and rising; shelf life 18 months (12 months for the 20-litre size)

Satisfies EN 1504-2:2004

AKW

Height-adjustable worktop for sinks and hobs, wheelchair-accessible

• Height range 678mm-1100mm -- covers both standing users and wheelchair users at the same worktop without a separate lowered unit
• Parallel drive actuators provide 700N per column, lifting speed 30mm/s -- powered movement, not a manual crank or gas-strut mechanism
• ‘Safe Sense’ lifting technology as standard; a safety strip is available as an extra for more sensitive stop detection, specifically recommended for vulnerable users
• Stocked in 1000mm and 1400mm straight, 1600mm corner -- made-to-measure runs from 500mm up to 3000mm, or L-shaped up to 3000x3000mm
• 5 year manufacturer’s warranty on the unit, 2 years specifically on moving parts -- the moving parts warranty is shorter, worth flagging separately when budgeting maintenance
• Modesty panels available as an accessory to conceal the fixings and mechanism underneath, in four finishes

AKW

PVC shower and bathroom wall panels

• BS EN 13501-1 Class D fire rated when adhered to a non-combustible substrate
• 15 year warranty
• 10mm thick, 600mm or 1000mm panel widths at 2500mm length
• Hollow internal channel construction -- lightweight, but needs the separate Accessory Fixing Kit (solid spacers) before fitting anything weight-bearing like grab rails or seats
• Fits directly over most existing surfaces including tiles
• Tongue and groove edge for a seamless join between panels
• Four finishes: White Gloss, White Marble Matt, Concrete Matt, Dark Graphite Matt

Satisfies BS EN 13501-1

AKW

High-pressure laminate shower and bathroom wall panels

• 35 year warranty
• Finished on both sides -- either face can be used, more forgiving if one side gets scuffed on site
• WPS plywood substrate bonded with HPL for a waterproof surface
• Structural grade -- shower seats and grab rails can be fitted directly without extra backing
• Panels fit directly over existing tiles
• 12mm thick, panel widths from 308mm to 1220mm at 2440mm length
• Six colour options: White Gloss, Savannah, Quartz, Black Marble, White Marble, Matt Grey

AKW

Shower riser rail with horizontal grab rail, T or L configuration

• 1200mm vertical riser rail with 600mm connecting horizontal grab rail
• Non-handed -- installs as T or L configuration to suit the user
• Maximum weight load 100kg / 16st on the riser rail, 150kg / 23.5st on the horizontal rail -- the two parts are not rated the same
• Height-adjustable handset holder, fits either side of the riser rail
• Aluminium alloy construction, lifetime warranty
• Does not include the shower valve, handset or hose

AKW

HPL-faced MDF and plywood wall panels for wet rooms and bathrooms

• 35 year warranty
• 11mm thick throughout -- three sizes: 600mm and 900mm tongue-and-groove, 1200mm square edge
• MDF core (T&G sizes) or 5-layer plywood core (square edge), FSC certified
• 16 decor options including marble, shimmer and matt finishes
• Structural enough for shower seats and grab rails to be fixed directly
• Any exposed core at edges must be covered with sealed aluminium profile -- this is a manufacturer requirement, not optional finishing

AKW

Slip-resistant PVC wet room and bathroom flooring

• Class C barefoot wet ramp test (DIN 51097) -- the highest slip-resistance classification, tested barefoot on wet soapy surfaces rather than the lower-bar shod test
• R10 rated (DIN 51130) -- deliberately not R11/R12, since that abrasive a finish is unsuitable for bare feet in a care setting
• 2mm total thickness, 0.75mm wear layer, Class 34 commercial very heavy wear rated
• DSDC (University of Stirling) dementia-friendly accreditation -- seven of eight colours rated 1a, no large speckle pattern that can read as debris to someone with dementia
• Reaction to fire: EN 13501-1 Class Bfl-s1
• 10 year guaranteed slip resistance
• Supplied in 2m width rolls, cut to order in 0.5m increments -- minimum order 0.5 x 2m

Satisfies EN 13553 & EN 13845

AKW

Straight grab rail, 300/450/600mm, stainless or matt black

• 304 stainless steel, 32mm rail diameter
• Maximum weight load 150kg / 23.5st
• 9 fixing points per bracket, 2 brackets per rail (18 total)
• Matt black finish offers colour contrast for visual impairment, not just a style option
• Fixing points concealed by a removable bracket cover -- protects internals from water and dirt, easier to clean
• Wall fixings not supplied

Channel Safety Systems

LED emergency exit sign with full legend set

• Viewing distance 30-32m, relevant when checking exit sign spacing meets BS 5266 escape route coverage rather than just relying on lux output alone
• 3 hour minimum emergency duration, maintained or non-maintained
• IP20 -- indoor dry-area rating only, not a substitute for the IP65 Solent bulkhead in exposed corridors or external escape routes
• Nickel Cadmium battery, 3.6V 1200mAh
• Downlight panel LEDs illuminate the exit door itself, not just the sign legend
• Supplied with full legend set (up/down/left/right arrows)

Satisfies BS EN 60598-2-22

Channel Safety Systems

IP65 LED emergency bulkhead, wall or ceiling mounted

• IP65 rated -- rare for a bulkhead at this size, suitable internally or externally (covered walkways, plant rooms) without a separate weatherproof variant
• 150 lm emergency output, 3 hour minimum duration
• Lithium LiFePo4 battery, less than 24 hour recharge period
• Maintained or non-maintained operation, switchable
• Semi-recessing kit available as an accessory if a flush-mounted look is wanted
• 3.2V 1500mAh battery, quiescent draw 35mA

Satisfies BS EN 60598-1:2008

Contour

Anti-ligature radiator guard for secure and mental health care environments

• Grille perforated with 2mm holes at 4mm centres, tested by a UKAS-accredited lab to exceed IP3x -- stops objects 2.5mm or larger being inserted, reducing the grille itself being used as a ligature point
• Anti-ligature TRV shroud fitted as standard, plus a wide range of security fastenings to stop unauthorised access inside the casing
• Contour cannot guarantee the casing stays under 43°C surface temperature on anti-ligature models -- the security grille restricts the convection that keeps a standard LST guard cool, so this is a genuine trade-off against the LST range, not a like-for-like swap
• 1.5mm Zintec steel standard, aluminium option for wet or humid environments
• Available floor or wall mounted, square or gradient top, same four configurations as the standard LST range
• 5 year warranty on the guard, 10 year on the radiator emitter
• Available as guard-only retrofit over an existing panel or fin radiator, not just as a complete new system

Satisfies BS EN 60529 (IP3x)

Contour

Low surface temperature radiator guard for healthcare and care settings

• 1.5mm Zintec steel casing, 2mm available where extra strength is needed
• 10mm radius edges and bullnose corners -- reduces injury if someone falls against it
• Full drop-down front door for cleaning access, not a fixed panel
• BioCote antimicrobial coating as standard on RAL 9003 white finish
• Magnelis steel casing option for wet rooms and humid areas
• Operating pressure 10 bar, tested to 13 bar
• Single casing length 600mm to 2000mm, height 550mm to 1150mm
• RotaRad valve kits standard on all LSTs -- can be removed if not required

Satisfies BS EN 442

Contour

Retrofit valve kit that pivots a radiator down for cleaning without draining the system

• WRAS, KTW and ACS approved -- can be retrofitted to any standard panel radiator, not just Contour’s own range
• Radiator pivots down to floor level for cleaning behind it and the wall, without draining or isolating the heating system
• Design life of 50 years minimum
• Body available in yellow brass, red brass, or stainless steel (AISI 316) depending on water conditions
• Fully compatible with Contour’s DeepClean range, but not exclusive to it
• Flame-free installation

Freefoam

Exterior wall cladding for dormers, gable ends and full facades

• Fire rating varies by colour -- white, Pale Gold, Sand, Misty Grey and a few others hold D-s3,d2, but darker colours (Storm Grey, Anthracite Grey, Cappuccino and others) drop to Class E because of the ASA skin needed for their colourfastness. Same D rating limits under Building Regs either way, but worth checking the specific colour before assuming the fire class
• Permitted 1m or more from a relevant boundary on buildings up to 18m per Part B -- taller or closer needs a specific check
• Continuous ventilation required -- minimum 25mm gap between cladding and the breather membrane/insulation/wall, maintained top to bottom
• 25mm x 50mm battens at 400mm centres for all profiles
• Horizontal break (drip trim) required above 6m height; vertical break required beyond 10m run
• 5-10 year guarantee depending on colour and profile -- darker colours generally carry the shorter 5 year term

Satisfies Building Regulations Part B (fire safety), CSTB accredited

Freefoam

PVC-U guttering and downpipe system

• Co-extruded with a white interior regardless of exterior colour -- keeps heat absorption and expansion down, since a dark exterior surface alone can exceed the PVC softening point in direct sun
• 50 year guarantee on registered white installations, 10 year on other colours (20 year standard without registration)
• Gutter flow capacity, outlet at centre of run: half round 1.90 l/sec, square 2.20 l/sec, ogee 3.90 l/sec, deep 3.77 l/sec (level; higher again at 1:600 fall)
• Cast iron style range available for period-appropriate refurbishment, same fitting system as the standard PVC range
• Compatible with other manufacturers’ rainwater systems via adaptors -- useful for partial replacement without a full strip-out
• Fascia brackets fixed at max 1m centres generally, reduced to 800mm in areas prone to heavy snowfall (per BS 6367:1983)

Satisfies BS 4576, BS EN 12200, BS EN 607, BS EN 1462

Freefoam

PVC-U/PVC-UE fascia, soffit and rainwater roofline system

• 50 year guarantee on white profiles, 10 year on coloured and woodgrain (20 year standard without online registration)
• Magnum fascia boards BBA-tested to support up to 50kg load per metre of eaves tiles at all roof pitches
• Gutter brackets tested to BS EN 1462:2004, no failure at 420N test weight
• Fixings (Plastops) are A4 marine-grade stainless steel -- corrosion resistant, will not rust or stain the profile
• Fire classification D-s3, d2
• 100% lead-free, REACH compliant, will not support bacterial or fungal growth
• Standard 5m lengths, fascia thickness from 8mm (refurbishment overcap) to 25mm (Magnum Xtra full-replacement)
• This is the roofline system (fascia/soffit/gutters) specifically -- Freefoam publish separate documentation for their cladding and rainwater ranges

Satisfies BS EN 13245-2:2008, BS EN 10088-3:2014, BBA Certificate 99/3585/C

Furnitubes

Bolt-down or pedestal-mounted external litter bin

• Two installation types depending on ground: bolt-down for level sites (includes a rodent bait tray as standard), pedestal-mounted for sloped sites so the door still opens on a horizontal plane
• Three sizes -- 90 litre (ZEN500), 125 litre (ZEN520) bolt-down, and 80 litre (ZEN580) pedestal
• Pedestal version needs 500mm root depth (150mm gap above ground, 350mm embedded in the concrete foundation) -- worth checking against buried services before specifying
• Integral lid on all bins prevents rainwater ingress into the liner
• Steel triple-process powder coated, or Grade 304/316 stainless steel satin or bright polished -- same material choice logic as the Zenith bollards, so a matching set is straightforward to specify
• Optional cigarette stubber and separate ash waste liner, laser-cut LITTER/RECYCLING wording

Horne Engineering

Type H-1503 thermostatic mixing valve, installation and commissioning instructions

• Dead leg from the valve to the outlet must not exceed 2 metres
• Hot water supply temperature 55C to 65C, cold 5C to 20C
• Standard temperature adjustment range 35C to 46C
• Mixed water set point for healthcare use must not exceed 46C
• Cold isolation test: no more than 120ml flow in 60 seconds after 5 second delay

Satisfies TMV3 approved, HTM 04-01 Type 3

Horne Engineering

Thermostatic mixing valve with integral check valves and strainers

• Factory temperature setting 41C, adjustable 35C to 50C
• Hot water supply temperature range 52C to 85C
• Maximum static pressure 10 bar
• Maintained supply pressure range 0.2 to 5 bar
• WRAS approved, available in bronze or chromium plated finish

Satisfies TMV3 approved, LP and HP designations

Howdens

Base, wall and tower cabinets, standard and handleless

• This manual includes a dedicated Inclusive Kitchens section (Section 14) alongside the standard cabinet ranges -- worth requesting directly from a Howdens depot for care/accessible-specific layouts rather than assuming a standard run works
• Standard cabinet height 720mm full height / 557mm standard / 900mm extra tall -- worktop height is 890mm on standard cabinets (based on 38mm worktop)
• Handleless profile system elevates worktop height by 30mm compared to standard cabinet ranges -- relevant if matching heights across a mixed standard/handleless kitchen
• Granite and quartz (solid surface) worktops cannot use the standard bracket-and-screw fixing -- silicone fixing is required instead, and a metal support bar is needed under any unsupported span (e.g. where an appliance sits between cabinets)
• Dedicated sink base cabinets are recommended over adapting a standard base cabinet -- explicitly flagged as easier to install correctly
• Wall cabinets require confirmation the wall construction can take the loaded cabinet weight before fixing -- the manual defers to a professional if there’s any doubt, since wall fixing screws aren’t supplied (wall type determines the correct fixing)

James Hardie

Cement-based tile backer board for walls, floors and worktops in wet areas

• Fully non-combustible -- A1,S1-d0 fire classification, not just fire-resistant
• HardieBacker 500 is the heavier, thicker option (12mm, 13.8kg) for higher load applications; 250 is 6mm and lighter (9kg) for standard wall/floor tiling
• Tile weight carrying capacity 100kg/m² on both variants -- contact James Hardie technical department before specifying heavier tiles beyond this
• No asbestos, gypsum, glass fibre or formaldehyde in the composition
• 10 year limited product warranty
• Suitable for wet rooms, steam rooms, saunas and pool surrounds -- HardieBacker 500 specifically can also be used as backing for domestic boilers

Satisfies EN 12467; EN 13501-1 A1,S1-d0; BBA 04/4100

James Hardie

External weatherboard cladding, cedar or smooth texture

• 8mm thick fibre cement plank -- Portland cement, milled sand, cellulose fibres, no asbestos
• Does not form a weatherproof cladding on its own -- a breather membrane is required behind it to achieve the weatherproof barrier
• Flexural strength drops from >10 MPa dry to >7 MPa wet -- a real, quantified difference worth noting rather than assuming dry-tested figures hold up in service
• 21 colours, two textures (cedar, smooth), factory-primed with ColorPlus coating
• Substructure fixing centres max 600mm
• Cut edges must be sealed with HardieSeal edge coating before install if boards are cut to size on site

Satisfies EN 12467 Type A, Class 2; BBA 04/4147

Lorient

Combined intumescent fire, smoke and acoustic door seal

• Designed so the seal fits correctly regardless of which way round it’s installed -- maintains the smoke seal specifically at ironmongery points, a common weak spot the brochure flags separately
• Covers 30, 60, 90 and 120 minute applications across four widths (10x4mm to 25x4mm)
• CERTIFIRE CF330 + CF341, BBA 92/2841
• Durability tested to 100,000 cycles
• PVC-encased sodium silicate intumescent core with elastomeric fins -- the intumescent activates at 100-150°C, expanding 5-10x its original size well before the fins themselves would degrade
• Fitted with heavy duty self-adhesive backing -- can bond to MDF, which the brochure notes is usually difficult to get a reliable adhesive bond on

Satisfies BS 476-22:1987, BS EN 1634-1:2008, BS 9999:2017

Lorient

Automatic threshold drop seal

• Mechanism lifts the seal clear of the floor when the door opens, and drops automatically on closing -- self-levelling, so it still seals effectively on an uneven floor
• Covers fire, smoke and acoustic performance in one product -- CERTIFIRE CF5179, UL R27972
• Directly answers a genuine gap: perimeter and fire seals alone don’t address the threshold, and BS 9999 requires a threshold seal wherever the gap exceeds 3mm on a fire and smoke door
• Durability tested to 100,000 cycles
• Works with a slimline threshold plate (as little as 5mm high) specifically so it doesn’t create a trip hazard for wheeled traffic -- relevant for hoists, wheelchairs and trolleys in a care setting
• A cladding kit variant extends the same product to 60-minute FD60 doors

Satisfies BS 476-20/22:1987, BS EN 1634-1:2014, BS EN 1634-3:2004

Rockpanel

Basalt stone-wool-based rainscreen facade cladding board

• FS-Xtra (9mm) is the specific variant for where the greatest fire safety is required -- achieves European fire class A2-s1,d0, the class relevant for high-rise and fire-sensitive buildings, not the standard Durable/Xtreme range
• Durable (6-8mm) for regular facade/roofline use; Xtreme (8mm) adds impact resistance specifically for ground-level applications prone to knocks
• BRE Global A+ or A rated across the range on Life Cycle Assessment -- independently assessed, not a manufacturer self-declared rating
• Non-directional boards (except Woods finish) -- genuinely simplifies installation and reduces waste versus a directional material
• ProtectPlus coating (standard on most finishes) is self-cleaning and graffiti-resistant without affecting gloss or colour when cleaned
• Basalt-based -- 1m³ of raw material produces over 400m² of board, and the material is recyclable

Satisfies ETA-07/0141 and related ETAs; European fire class A2-s1,d0 (FS-Xtra)